Motorola PMP 320 Скачать руководство пользователя

Страница: 22 / 146

1-22

PMP320HDW2v1

Preliminary

JUL 2010

PMP 320 Hardware Installation

Site preparation

Table 1-2 CAP 320 Antenna Specifications

CAP 320 Antenna Specifications

Antenna Beam Width

16.5 dBi gain Dual Polarity +/- 45 4 sector

application (actual 3 dB antenna pattern: 60
degree horizontal

Table 1-3 CAP 320 Physical Specifications

CAP 320 Physical Specifications

Power Consumption

< 25 Watts

Temperature

-40° F to +131° F (-40° C to +55° C)

Wind Survival

118 miles/hr (190 km/hr)

Dimensions (LxWxD)

Integrated: ~711 x 195 x 240mm

Connectorized: ~330 x 195 x 140mm

Weight

Integrated: 5.5 kg
Connectorized: 2.2 kg

For additional information regarding spectrum and frequency information, refer to the

PMP

320 Administration and Configuration Guide

located at:

http://motorola.wirelessbroadbandsup-

port.com/support/library/

Site preparation

Review the following site requirements before selecting the site for the installation of the
PMP 320 CAP:

•

Verify that a good Earth Ground can be achieved at the site.

•

Verify that the power to the site is reliable and can be backed up by an uninterruptible
power supply (UPS).

•

Verify that access to the site is easy if an urgent need arises. (It can take up to forty-five
minutes to key-down the transmitters at certain locations.)

•

Verify that the site is secure.

•

Be sure to negotiate a contract with the site owner that allows easy swap-out of existing
equipment without an added cost.

•

Accurately measure the latitude and longitude of the location for future reference.

Содержание PMP 320


















































































































































Результаты поиска

Содержание PMP 320

Отзывы:

Похожие инструкции для PMP 320

Бренды по названию

Популярные бренды

Motorola PMP 320, Установка оборудования

Результаты поиска

Содержание PMP 320

Отзывы:

Похожие инструкции для PMP 320

Бренды по названию

Популярные бренды