Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 174

background image

73

CHAPTER 7 VARIOUS SETTINGS

7

7.3 Offset/Gain Sett

ing

●

Configure the offset/gain setting in accordance with the actual use situation.
Connection to the CC-Link IE Field Network is not required.

●

Configure the offset/gain setting in the range satisfying the following condition. When the setting value out of the range is
configured, the maximum resolution and accuracy of the module may not fall within the range shown in the following
performance specifications.

• I/O Conversion Characteristic of D/A Conversion (

Page 152, Appendix 4)

●

Because the offset value and gain value are written to the nonvolatile memory in the D/A converter module, the set
values can be used even after the module is powered on and off.

●

Configure the offset/gain setting in the condition of "Offset value < Gain value".
The offset and gain values are checked in the D/A converter module when Initial data setting request flag (RY9) is turned
on and off with the user range setting 1 or user range setting 2 set to Range setting (address: 0103

H

). If a wrong condition

(offset value

≥

gain value) is set, an error occurs. The error code (040

H

) is stored in Latest error code (RWr0) when they

are checked, Error flag (RXA) is turned on, and the ERR. LED turns on.

«
...
73
74
75
76
77
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: Waterway Страницы: 16

Бренд: Magnescale Страницы: 132

Бренд: Canarm Страницы: 3

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: RadioMaster Страницы: 10

Бренд: Xblue Networks Страницы: 2

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

AMES 4000SS Series

Бренд: Watts Страницы: 8

Бренд: Technische Alternative Страницы: 68

Бренд: EVERSPRING Страницы: 3

Бренд: elsner elektronik Страницы: 2

769N FireLock NXT Series

Бренд: Victaulic Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды