Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 174

background image

72

7.3

Offset/Gain Setting

When the user range setting is used, configure the offset/gain setting with the following operations.
When factory default settings are used, the offset/gain setting is not required.

1.

Power off the module.

2.

Set "O/G" for "x10" of the station number setting

switch.

3.

Power on the module to check the LED is in the

following status.

RUN LED: OFF
O/G LED: ON

4.

Select the setting target using the SET/SEL button.

5.

For the selected channel, adjust the analog output

value by using the "+" and "–" switches.

Pressing the "+" switch increases the analog output
value. Pressing the "–" switch decreases the analog
output value.

6.

Keep pressing the button until the RUN LED

turns on.

After the RUN LED turns on, release the button.
While the RUN LED is on, the offset value or gain value
is being written to the nonvolatile memory.
After the writing, the RUN LED turns off.
After checking that the RUN LED turns off, go to the
next step.

7.

When setting another channel, go back to step 4.

8.

After setting all the channels, power off the module.

: OFF

: ON

[User range setting 1 (-10 to 10V)]

CH1: Offset

CH1: Gain

CH2: Offset

CH2: Gain

CH3: Offset

CH3: Gain

CH4: Offset

CH4: Gain

[User range setting 2 (0 to 20mA)]

CH1: Offset

CH1: Gain

CH2: Offset

CH2: Gain

CH3: Offset

CH3: Gain

CH4: Offset

CH4: Gain

Button

Button

Data are being written.

The write is completed.

Keep pressing the button.

«
...
72
73
74
75
76
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: Samsung Страницы: 32

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: Quectel Страницы: 90

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: Rain Bird Страницы: 138

Бренд: Watlow Страницы: 4

Бренд: Samson Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды