Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 52

Страница: 52 / 174

Do not slide modules from the edge of the DIN rail when mounting them. Doing so may damage the metal part located on the
back of the module.

(2) Removal procedure

Remove the modules from the DIN rail by reversing the above procedure.

(3) Applicable DIN rail model (compliant with IEC 60715)

• TH35-7.5Fe
• TH35-7.5Al

Hitch the upper hook of the DIN rail stopper to the

top of the DIN rail.

Slide the DIN rail stopper up to the left side of the

modules.

Hold the DIN rail stopper in the direction opposite to

the arrow on the stopper and tighten the screw with
a screwdriver.

Install the DIN rail stopper on the right side of the

module in the same procedure.

Install the stopper upside down for the right side.

Hitch the hook to
top of the DIN rail

DIN rail
stopper

Содержание NZ2GF2B-60DA4















































































































































































Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды

Mitsubishi NZ2GF2B-60DA4, Руководство пользователя

Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды