Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 174

background image

1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full attention
to safety to handle the product correctly.
The precautions given in this manual are concerned with this product only. For the safety precautions of the
programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety precautions are classified into two levels: "

WARNING" and "

CAUTION".

Under some circumstances, failure to observe the precautions given under "

CAUTION" may lead to

serious consequences.
Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future
reference.

[Design Precautions]

WARNING

●

In the case of a communication failure in the network, data in the master module are held. Check Data
link status (each station) (SW00B0 to SW00B7) and configure an interlock circuit in the program to
ensure that the entire system will operate safely.

●

Do not use any "use prohibited" signals as a remote input or output signal. These signals are reserved
for system use. Do not write any data to the "use prohibited" area in the remote register. If these
operations are performed, correct operation of the module cannot be guaranteed.

●

Configure safety circuits external to the programmable controller to ensure that the entire system
operates safely even when a fault occurs in the external power supply or the programmable controller.
Failure to do so may result in an accident due to an incorrect output or malfunction.
(1) The status of analog output depends on the setting of various functions that control the analog

output. Exercise great caution when setting those functions. For details of analog output status,
refer to the Page 76, Section 8.4.

(2) Due to failure of the output element or internal circuit, normal output may not be obtained

correctly. Configure an external circuit for monitoring output signals that could cause a serious
accident.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,
resulting in minor or moderate injury or property damage.

«
1
2
3
4
5
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: Bartlett Страницы: 30

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Panasonic Страницы: 16

Бренд: rada Страницы: 16

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Oceanic Страницы: 11

Бренд: X Rocker Страницы: 38

Бренд: Zamel Страницы: 23

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zander Aachen Страницы: 44

Extra Free ROB-01/12-24V

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 14

Бренд: Allen-Bradley Страницы: 16

Бренд: D+H Страницы: 2

Бренд: phytron Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды