Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 174

background image

3

[Wiring Precautions]

[Startup and Maintenance Precautions]

[Startup and Maintenance Precautions]

CAUTION

●

Use applicable solderless terminals and tighten them within the specified torque range. If any spade
solderless terminal is used, it may be disconnected when a terminal block screw comes loose,
resulting in failure.

●

Check the rated voltage and terminal layout before wiring to the module, and connect the cables
correctly. Connecting a power supply with a different voltage rating or incorrect wiring may cause a fire
or failure.

●

Tighten the terminal block screws within the specified torque range. Undertightening can cause short
circuit, fire, or malfunction. Overtightening can damage the screw and/or module, resulting in drop,
short circuit, fire, or malfunction.

●

Prevent foreign matter such as dust or wire chips from entering the module. Such foreign matter can
cause a fire, failure, or malfunction.

●

Place the cables in a duct or clamp them. If not, dangling cable may swing or inadvertently be pulled,
resulting in damage to the module or cables or malfunction due to poor contact.

●

Do not install the control lines or communication cables together with the main circuit lines or power
cables. Keep a distance of 100mm or more between them. Failure to do so may result in malfunction
due to noise.

●

When disconnecting the cable from the module, do not pull the cable by the cable part. For the cable
with connector, hold the connector part of the cable. For the cable connected to the terminal block,
loosen the terminal screw. Pulling the cable connected to the module may result in malfunction or
damage to the module or cable.

●

When an overcurrent caused by an error of an external device or a failure of the programmable
controller flows for a long time, it may cause smoke and fire. To prevent this, configure an external
safety circuit, such as a fuse.

●

Mitsubishi programmable controllers must be installed in control panels. Wiring and replacement of a
module must be performed by qualified maintenance personnel with knowledge of protection against
electric shock. For wiring methods, refer to "INSTALLATION AND WIRING" in this manual.

WARNING

●

Do not touch any terminal while power is on. Doing so will cause electric shock or malfunction.

●

Shut off the external power supply (all phases) used in the system before cleaning the module or
retightening the terminal block screws. Failure to do so may cause the module to fail or malfunction.

CAUTION

●

Do not disassemble or modify the module. Doing so may cause failure, malfunction, injury, or a fire.

●

Do not drop or apply strong shock to the module. Doing so may damage the module.

●

Shut off the external power supply (all phases) used in the system before mounting or removing a
module. Failure to do so may cause the module to fail or malfunction.

«
...
3
4
5
6
7
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: ABATEC Страницы: 8

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

ServeRAID M5014

Бренд: IBM Страницы: 106

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: Access Страницы: 12

Бренд: Wavelink Страницы: 69

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Samson Страницы: 73

Бренд: Newport Страницы: 417

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды