Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 174

background image

56

(2) Precautions

(a) Laying Ethernet cables

• Place the Ethernet cable in a duct or clamp them. If not, dangling cable may swing or inadvertently be pulled,

resulting in damage to the module or cables or malfunction due to poor contact.

• Do not touch the core of the connector of the cable or the module, and protect it from dirt and dust. If any oil

from your hand, or any dirt or dust sticks to the core, it can increase transmission loss, causing data link to
fail.

• Check the following:

• Is any Ethernet cable disconnected?
• Does any Ethernet cable short?
• Are the connectors securely connected?

(b) Broken cable latch

Do not use Ethernet cables with broken latches. Doing so may cause the cable to unplug or malfunction.

(c) Connecting and disconnecting the Ethernet cable

Hold the connector part when connecting and disconnecting the Ethernet cable. Pulling the cable connected to
the module may result in damage to the module or cable or malfunction due to poor contact.

(d) Connectors without Ethernet cable

To prevent dust from entering the module, attach the provided connector cover.

(e) Maximum station-to-station distance (Maximum Ethernet cable length)

The maximum station-to-station distance is 100m. However, the distance may be shorter depending on the
operating environment of the cable. For details, contact the manufacturer of the cables used.

(f) Bending radius of the Ethernet cable

There are restrictions on the bending radius of the Ethernet cable. Check the bending radius in the
specifications of the Ethernet cables used.

«
...
56
57
58
59
60
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: C&C Страницы: 17

Бренд: Hunter Страницы: 2

Бренд: Tektronix Страницы: 112

Бренд: micro-trak Страницы: 44

Бренд: Conductrix Wampfler Страницы: 23

Бренд: Carel Страницы: 2

Бренд: Timotion Страницы: 9

Бренд: Gain Electronic Страницы: 17

Бренд: Vexve Страницы: 24

972LM Security?

Бренд: Chamberlain Страницы: 4

Бренд: Zeversolar Страницы: 8

Бренд: ECUE Страницы: 39

Бренд: Regada Страницы: 41

Бренд: Allen-Bradley Страницы: 8

Бренд: Castell Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды