Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 174

background image

161

APPENDICES

A

Appendix 7 EMC and Low

Voltag

e Directives

Appendix 7.1 Measures to comply w

ith the

E

M

C Directive

(b) Noise filter (power supply line filter)

A noise filter is a component which has an effect on conducted noise. Attaching the filter can suppress more
noise. (The noise filter has the effect of reducing conducted noise of 10MHz or less.)
Connect a noise filter to the external power supply of a main module and the external power supply of an
extension module. Use a noise filter with the damping characteristics equivalent to those of MA1206
(manufactured by TDK-Lambda Corporation). Note that a noise filter is not required if the module is used in
Zone A defined in EN61131-2.

The precautions for attaching a noise filter are described below.

• Do not bundle the cables on the input side and output side of the noise filter. If bundled, the output side

noise will be induced into the input side cables from which the noise was filtered.

• Ground the noise filter grounding terminal to the control panel with the shortest cable possible (approx.

10cm).

Filter

Induction

Input side

(power supply side)

Output side

(device side)

Filter

Input side

(power supply side)

Output side

(device side)

Noise will be induced when the input
and output wires are bundled.

Separately install the input and
output wires.

«
...
161
162
163
164
165
...
»

Содержание NZ2GF2B-60DA4















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NZ2GF2B-60DA4

Бренд: Bartec Страницы: 26

Бренд: V2 Страницы: 48

Бренд: Samson Страницы: 52

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: WAM Страницы: 62

Бренд: walimex Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренд: wallas Страницы: 2

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Бренд: Yealink Страницы: 8

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

iSteam 2.0 Control

Бренд: mr. steam Страницы: 16

Бренд: Sygonix Страницы: 12

Бренд: Nordelettronica Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды