Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 43

Страница: 43 / 174

CHAPTER 4 THE PROCEDURE BEFORE OPERATION

CHAPTER 4

THE PROCEDURE BEFORE
OPERATION

This section describes the procedure before operation.

To replace the module, refer to this section.

To replace the module, follow the procedure described below.

• Power off the module and remove the D/A converter module.
• Prepare a new D/A converter module and perform the procedure above from "Setting a station number" to

"Parameter settings and programming". (The network parameter of the master station does not need to be set
again.)

• When using the user range setting, perform the offset/gain setting.
• After checking the operation, restart the control.

Page 45, Section 6.1

Page 46, Section 6.2,
Page 48, Section 6.3

Page 52, Section 6.4,
Page 54, Section 6.5,
Page 57, Section 6.6

Page 63, Section 7.1,

Page 68, Section 7.2.1

Page 105, CHAPTER 9

Page 72, Section 7.3

Check box

Set the station number for an D/A converter module.

Setting a station number

Connection

When using an extension module, connect the extension module to the
D/A converter module.
After that, mount the D/A converter module to a DIN rail.

Connect the D/A converter module to a power supply, Ethernet cables,
and external devices.

Parameter settings and programming

Set parameters and create a program.

Offset/gain setting

To use user range settings, configure the offset/gain setting.

Wiring

Содержание NZ2GF2B-60DA4















































































































































































Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды

Mitsubishi NZ2GF2B-60DA4, Руководство пользователя

Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды