Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 70

Страница: 70 / 174

7.2

Changing the Parameter

7.2.1

Changing the network configuration

When changing the network configuration diverting the created project, set the parameter in the following procedure.

Power off the module.

Connect the modules again according to the desired network configuration.

Power on the module.

Display the "CC IE Field Configuration" window.

• When the master/local module is the QJ71GF11-T2

Project window

[Parameter]

[Network Parameter]

[Ethernet/CC IE/MELSECNET]

button

• When the master/local module is the LJ71GF11-T2

Project window

[Parameter]

[Network Parameter]

[CC IE Field]

button

Drag and drop a module to set the slave station. Input a numerical value to set the station number
of the station. Change the value as necessary.

Close the "CC IE Field Configuration" window.

[CC IE Field Configuration]

[Close with Reflecting the Setting]

Click the

button to display the refresh parameter setting window.

Содержание NZ2GF2B-60DA4















































































































































































Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды

Mitsubishi NZ2GF2B-60DA4, Руководство пользователя

Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды