Mitsubishi NZ2GF2B-60DA4 Скачать руководство пользователя страница 51

Страница: 51 / 174

CHAPTER 6 INSTALLATION AND WIRING

6.3 Installa

tion

6.3.2 Mo

unting

the modules on a DIN r

ail

6.3.2

Mounting the modules on a DIN rail

An example of the use of the DIN rail stopper is described in the following procedure. Fix the module according to the
manual of the DIN rail stopper used.

(1) Mounting procedure

Pull down all DIN rail hooks on the back of the

modules.

The levers should be pulled down until it clicks.

Hang the upper tabs of the modules on a DIN rail,

and push the modules in position.

Lock the DIN rail hooks to the DIN rail to secure the

modules in position.

Push each hook up until it clicks. If the hooks are
beyond the reach, use a tool such as a screwdriver.

Loosen the screw on DIN rail stopper.

Hitch the bottom hook of the DIN rail stopper to the

bottom of the DIN rail.

Hitch the hook according to the orientation of the arrow
on the front of the stopper.

Hook

Hitch the hook to
bottom of the DIN rail

Содержание NZ2GF2B-60DA4















































































































































































Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды

Mitsubishi NZ2GF2B-60DA4, Руководство пользователя

Результаты поиска

Содержание NZ2GF2B-60DA4

Отзывы:

Похожие инструкции для NZ2GF2B-60DA4

Бренды по названию

Популярные бренды