Mitsubishi 1992 3000GT Скачать руководство пользователя страница 889

Страница: 889 / 1308

SERVICE BRAKES On-vehicle Service

rod

Operat
rod

Lock nut

BRAKE PEDAL CHECK AND ADJUSTMENT

BRAKE PEDAL HEIGHT

1. Turn off the carpet etc. at under the brake pedal.

Measure the brake pedal height as illustrated. If the brake
pedal height is not within the standard value, adjust as

follows.

Standard value (A): 177-182 mm (7.0-7.2 in.)

(1) Disconnect the stop light switch connector, loosen

the lock nut, and move the stop light switch to a

position where it does not contact the brake pedal
arm.

(2) Adjust the brake pedal height by turning the operating

rod with pliers (with the operating rod lock nut loos-

ened), until the correct brake pedal height is obtained.

(3) Screw in the stop light switch until it contacts the

brake pedal stopper (just before the brake pedal is
caused to move). Back off the stop light switch
to 1 turn and secure by tightening the lock nut.

(4) Connect the connector of the stop light switch.
(5) Check to be sure that the stop light is not illuminated

with the brake pedal released.

Reference value (B):

in.)

(6) On vehicles with automatic transaxle, check the

shift-lock mechanism. (Refer to GROUP 23
Transaxle Control.)

3. Return the carpet etc. to the original position.

BRAKE PEDAL FREE PLAY

1. With the engine stopped, press the brake pedal two or

three times. After eliminating the vacuum in the power

brake booster, press the pedal down by hand, and confirm

that the amount of movement before feeling resistance

is met (the free play) is within the standard value range.

Standard value (C): 3-8 mm

in.)

If the free play is less than the standard value, confirm

that the clearance between the stop light switch and brake
pedal is within the standard value.

If the free play exceeds the standard value, it is probably

due to excessive play between the

pin and brake

pedal arm. Check for excessive clearance and replace
faulty parts as required.

TSB Revision

Содержание 1992 3000GT





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1992 3000GT

Отзывы:

Похожие инструкции для 1992 3000GT

Бренды по названию

Популярные бренды

Mitsubishi 1992 3000GT, Руководство по обслуживанию

Результаты поиска

Содержание 1992 3000GT

Отзывы:

Похожие инструкции для 1992 3000GT

Бренды по названию

Популярные бренды