manualshive.com logo in svg

Mitsubishi 1992 3000GT, Руководство по обслуживанию

Поделиться
Скачать
Mitsubishi 1992 3000GT Скачать руководство пользователя страница 1249

HEATERS AND MANUAL

AIR CONDITIONING

 On-vehicle Service

Blower motor HI relay 

 to 1995 

ADJUSTMENT PROCEDURES

(1) Select a quiet area for testing. Duplicate conditions as

much as possible. Switch compressor on and off several

times to clearly identify compressor noise.
To duplicate high ambient conditions (high head pressure),

restrict air flow through condenser. Install manifold gauge

set to make sure discharge pressure doesn’t exceed 2,070

 (300 psi).

(2) Tighten all compressor mounting bolts, clutch mounting

bolt, and compressor drive belt. Check to assure clutch
coil is tight (no rotation or wobble).

(3) Check refrigerant hoses for rubbing or interference that

can cause unusual noises.

(4) Check refrigerant charge. (See “Charging System”.)
(5) Recheck compressor noise as in Step 1.
(6) If noise still exists, loosen compressor mounting bolts

and retorque. Repeat Step 1.

(7) If noise continues, replace compressor and repeat Step

1.

POWER RELAY CHECK

(1) Remove the radiator fan motor relays (HI) and (LO) from

the relay box on the right of the engine compartment.

(2) Remove the radiator fan motor relay (air conditioning)

 to 1993 models>, condenser fan motor relays (HI)

and (LO), and air-conditioning compressor relay from the

relay box on the left of the engine compartment.

(3) Remove the blower motor relay from the junction box.
(4) Remove the blower motor HI relay 

 to 1995 models>

from the blower case assembly.

(5) Check the continuity between terminals using a circuit

tester.

IDLE-UP OPERATION CHECK

(1) Before inspection and adjustment set vehicle in the follow-

ing condition:

l

Engine coolant temperature: 

 

l

Lights, electric cooling fan and accessories: Set to
OFF

l

Transaxle: Neutral (N or P for vehicles with 

l 

Steering wheel: Straightforward

(2) Check to be sure that the idling speed becomes the stan-

dard value when the air conditioning switch is switched
ON and the air conditioning is activated.

Standard value: 900   100 rpm

NOTE
Idle speed is controlled by the 

 system and is not

adjustable. If, idle speed is not within specifications, check
the ISC system.
(Refer to GROUP 13A   On-vehicle Service.)

TSB Revision

Содержание 1992 3000GT





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды