Mitsubishi 1992 3000GT Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 1308

background image

ENGINE

On-vehicle Service

(9) If there is a cylinder in which the compression pressure

or pressure difference is beyond the limit value, pour
in a small amount of engine oil through the spark plug
mounting hole, and repeat Steps (7) through (8).

1)

If the small amount of oil poured in causes the com-
pression pressure to rise, then it is likely that either

the piston ring, cylinder wall surface or both are worn
or damaged.

2) If the small amount of oil poured in does not cause

the compression pressure to rise, then valve seizure,
poor valve contact, or leakage from the gasket is
suspected.

the crankshaft position sensor connector.

(11) Re-mount the spark plugs and spark plug cables.

the diagnostic trouble code using the scan tool

or disconnect the negative

terminal of the battery,

leave it disconnected for more than 10 seconds, and

then re-connect it.

NOTE

This erases the trouble code due to the disconnection
of the crankshaft position sensor connector.

MANIFOLD VACUUM CHECK

(1) The vehicle should be repaired as follows before the

inspection.

l

Engine coolant temperature:

l

Lights, electric cooling fan, and accessories: OFF

l

Transaxle: Neutral (P for A/T)

(2) Connect a tachometer. (Refer to
(3) 1) <Non-Turbo>

Install a three-way joint to the vacuum hose connected

between the air intake plenum and the fuel pressure
regulator and connect a vacuum gauge to the joint.

2) <Turbo>

Install a three-way joint to the vacuum hose connected
between the air intake plenum and the fuel pressure
solenoid valve and connect a vacuum gauge.

(4) Start the engine and check that idle speed is within the

standard value range.

(5) Check the manifold vacuum.

Limit: 450

(18

LASH ADJUSTER CHECK

NOTE
If the clanging noise due to the lash adjuster produced immedi-
ately after the engine has started or during operation persists,
perform the following checks.

(1) Check the engine oil, and add or replace if necessary.

NOTE
(1) If the engine oil level is low, the air drawn in from

the oil strainer will be trapped in the oil passage.

TSB Revision

«
...
79
80
81
82
83
...
»

Содержание 1992 3000GT





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1992 3000GT

Бренд: Feniex Страницы: 6

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

DBALL2-HYUNDAI9

Бренд: Xpresskit Страницы: 13

2011 3500 Chassis Cab

Бренд: RAM Страницы: 92

v.LOGiC Intelligent Solution V5-NTG46

Бренд: Caraudio-Systems Страницы: 18

Бренд: A-Tach Страницы: 2

RVS systems RVS-M641

Бренд: Safe Fleet Страницы: 24

Бренд: Gator Страницы: 6

Бренд: F.lli Menabo Страницы: 16

Бренд: NavLinkz Страницы: 23

Бренд: Honda Страницы: 22

Бренд: Mercedes-Benz Страницы: 494

Бренд: Mazda Страницы: 1001

SHERPA SADDLE BAG JL

Бренд: Overland Outfitters Страницы: 2

Бренд: Quadratec Страницы: 8

Бренд: Audiovox Страницы: 2

Бренд: ZeroRPM Страницы: 41

Бренд: Nav TV Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды