Mitsubishi 1992 3000GT Скачать руководство пользователя страница 80

Страница: 80 / 1308

ENGINE

On-vehicle Service

COMPRESSION PRESSURE CHECK

(1) Prior to inspection, check to ensure that the engine oil,

starter motor and battery are in proper condition. Place
the vehicle in the following conditions.

Engine coolant temperature:

Lights, electric cooling fan and accessories: OFF

Transaxle: Neutral (P for

(2) Remove the spark plug cables.
(3) Remove all of the spark plugs.

(4) Disconnect the crankshaft position sensor connector.

NOTE
By so doing the engine control module stops performing
ignition and fuel injection.

(5) Cover the spark plug mounting holes with a shop towel,

crank the engine, and then check for foreign substances
deposited on the shop towel.

Caution
1.

When you crank the engine, keep away from the spark
plug mounting holes.

If a compression measurement is performed with wa-

ter, oil, fuel, etc. in the cylinder due to the cracks

in the cylinders, these substances heated to a very
high temperature will blow off the spark plug mounting
holes and could be dangerous.

(6)

a compression gauge in a spark plug mounting

(7) Set the throttle valve in a fully opened position, and crank

the engine to measure the compression pressure.

Standard value:

1,270

(185 psi)

rpm]

1,080

(156 psi)

rpm]

Limit:

min. 959

(139 psi)

rpm]

min. 792

(115 psi)

rpm]

(8) Measure the compression pressure in each of the cylin-

ders and check that the difference in compression pres-
sure between the individual cylinders is less than the

limit value.

Limit: max. 98

(14 psi)

TSB Revision

Содержание 1992 3000GT





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 1992 3000GT

Отзывы:

Похожие инструкции для 1992 3000GT

Бренды по названию

Популярные бренды

Mitsubishi 1992 3000GT, Руководство по обслуживанию

Результаты поиска

Содержание 1992 3000GT

Отзывы:

Похожие инструкции для 1992 3000GT

Бренды по названию

Популярные бренды