Mitsubishi Electric s-MEXT-G00 006 Скачать руководство пользователя страница 19

Страница: 19 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Mask of the terminal

Description

Energy Managment

Energy: 0000000kWh

Time: 0000000 h

Network transducer

active energy and hour counter display mask.

Visible if the network transducer is present and configured

Input/Output GSM modem

Status:

Stand-by ext.modem

Offline 000%

Timelnextncallr:0000 s

SMS Queue: 00

GSM modem

status display mask.

Visible if the GSM modem is present and configured

PAC-IF

MASTER

Mask confirming access to the Master PAC-IF013B-E card additional information section.

Press “Esc” to

return to the Master PAC-IF013B-E card status mask.

PAC-IF013B-E Master

Status: ON

Mode: COOLING

Step: 11

Communication: Online

Master PAC-IF info mask:

•

Status

•

Method

•

Communication

•

Adjustment step

PAC-IF013B-E Master

TH11: 10.0°C

TH5: 13.0°C
TH2: 09.0°C

Master PAC-IF info mask:

•

Suction temperature probe (TH11)

•

Two-phase temperature probe (TH5)

•

Liquid temperature probe (TH2)

PAC-IF013B-E Master

TH7: 10.0°C

Master PAC-IF info mask:

•

External temperature probe (TH7)

PAC-IF013B-E Master

Compressor Status: ON

Predefrost: OFF

Defrost: ACTIVE

Selfprotection: ACTIVE

Software ver. 000001

Master PAC-IF info mask:

•

Compressor status

•

Pre-defrost

•

Defrost

•

Self protection

•

PAC-IF SW version

PAC-IF

SLAVE1

Mask confirming access to the Slave 1 PAC-IF013B-E card additional information section.

Press “Esc” to return to the Slave 1 PAC

-IF013B-E card status mask.

Содержание s-MEXT-G00 006

































































































































Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды

Mitsubishi Electric s-MEXT-G00 006, Техническое руководство

Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды