Mitsubishi Electric s-MEXT-G00 006 Скачать руководство пользователя страница 30

Страница: 30 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Mask of the terminal

Description

N. Par.

--------------- P20.82
Aux TH sensor addr.129
status enable : N

Parameter for configuring the presence of the auxiliary temperature / humidity probe (address 129) (0:disabled-

1:enabled)

20.82

Freecooling





Mask confirming access to the Freecooling operation submenu. Press "Up" or "Down" to scroll the other masks
and "Esc" to return to the submenu.

Unit
  WITHOUT Freecooling

Mask displayed if the Free Cooling mode is not present.

--------------- P21.21
Cold Ramp value for
max position FC: 050%

Parameter for configuring the value of the cold ramp at which the Freecooling damper is at maximum opening

point

only visible after enabling Free Cooling

21.21

--------------- P21.09
Freecooling damper
reg. enable: N
--------------- P21.10
Freecooling damper
control type: Analogic

Parameter for configuring Freecooling damper regulation (N:disabled - Y:enabled) and parameter for configuring
the Freecooling damper control type (0:Digital - 1:Modulating)

21.09

21.10

--------------- P21.11
Freecooling damper
reg. set point: 03.0°C
--------------- P21.12
Freecooling damper
reg. band: 01.0°C

Parameter for setting the Setpoint (T_

ROOM

-T_

EXTERNAL

) for Freecooling damper control, and the parameter for

setting the Freecooling damper control band

21.11
21.12

--------------- P21.13
Freecooling damper
MIN opening: 000%
--------------- P21.14
Freecooling damper
MAX opening: 100%

Parameter for setting the Minimum Freecooling damper opening and parameter for setting the Maximum

Freecooling damper opening

21.13

21.14

--------------- P21.32
Freecooling damper
with CMP/V3V: Y
--------------- P21.33
Delay Freecooling
damper On after Off
CMP/V3V: 0180s

Parameter for setting the configuration of the simultaneous operation of Direct Freecooling and compressor, or 3-
way valve

Parameter for setting the delay for opening Freecooling after the compressor is switched off/the closing of the

cold water valve

Only visible if the parameter P21.32 is disabled

21.32

21.33

--------------- P21.15
Freecooling damper for
high humid. status: N
--------------- P21.16
%RH set to deact.
freec. damper: 60.0%RH

Parameter for configuring Freecooling damper management for high humidity and
humidity limit for disabling Freecooling damper

21.15
21.16

Содержание s-MEXT-G00 006

































































































































Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды

Mitsubishi Electric s-MEXT-G00 006, Техническое руководство

Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды