Mitsubishi Electric s-MEXT-G00 006 Скачать руководство пользователя страница 33

Страница: 33 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Mask of the terminal

Description

N. Par.

Fan





Access mask to fan submenu. Press "Up" or "Down" to scroll the other masks and "Esc" to return to the submenu.

--------------- P23.01
Fan nominal
speed: 070%

Parameter for setting the nominal speed of the internal fan

23.01

--------------- P23.02
Economy mode fan
status: N
--------------- P23.03
Fan speed in
economy mode: 50%

Parameter for configuring the internal fan Economy Mode function (N:disabled - Y:enabled)
Parameter for setting the internal fan speed with the Economy Mode function enabled

23.02
23.03

--------------- P23.07
Air Flow modulation
with inverter mod.
status: Y

Parameter for configuring the Internal fan modulation function for inverter compressor units (N:disabled -

Y:enabled)

Only visible with constant flow rate check and constant DeltaP disabled

23.07

--------------- P23.08
MIN fan speed when
modul. active: 050%

Parameter for setting the minimum speed of the internal fan in modulation for inverter compressor units
(maximum reduction of design speed)

23.08

--------------- P23.10
Fan speed when active
dehumidif.: 060%

Parameter for setting the fixed internal fan speed for units with inverter compressor in dehumidification

23.10

--------------- P23.11
Air pressure diff.
scan time: 060s

Parameter for setting the differential air pressure scan time and

parameter for configuring the EC condensation control function (N:disabled - Y:enabled)

23.11

--------------- P23.61
Post-ventilation
for el.heater status:Y
--------------- P23.62
Post-ventilation time
for el.heater: 060s

Parameters for configuring the post-ventilation function for the heaters and the post-ventilation time.

Visible when the electric heaters are present

23.61

23.62

--------------- P23.65
Const. flow rate set:
02500 m3/h

Parameter used to set the Constant flow rate control setpoint (divided by 100)

23.65

Содержание s-MEXT-G00 006

































































































































Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды

Mitsubishi Electric s-MEXT-G00 006, Техническое руководство

Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды