Mitsubishi Electric s-MEXT-G00 006 Скачать руководство пользователя страница 28

Страница: 28 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Mask of the terminal

Description

N. Par.

--------------- P20.06
Inv. compressor reg.
intergral time: 900s

Parameter for setting

Integral adjustment time

20.06

--------------- P20.07
Inv. compressor reg.
derivative time: 000 s

Parameter for setting the inverter compressor adjustment derivative time (units with inverter compressor)

20.07

--------------- P20.08
Dirty filters sensor
presence: N
--------------- P20.09
Fire/smoke sensor
presence: N

Parameter for configuring the dirty filters sensor (N:disabled - Y:enabled)

and for configuring the fire smoke sensor (N:disabled - Y:enabled)

20.08
20.09

--------------- P20.10
Flooding sensor
presence: N

Parameter for configuring the flooding sensor (N:disabled - Y:enabled)

20.10

--------------- P20.13
Remote ON/OFF
presence: N

Parameter for configuring the ON/OFF remote contact (N:disabled - Y:enabled).

20.13

--------------- P20.18
Regulation band in
cooling: 2.0°C
--------------- P20.19
Regulation band in
heating: 1.5°C

Parameter for setting the cooling regulation band and the heating regulation band

20.18
20.19

--------------- P20.20
Regulation band for
dehumidif.: 5%RH
--------------- P20.21
Regulation band for
humidification: 5%RH

Parameter for setting the dehumidification regulation band and the humidification regulation band

20.20

20.21

--------------- P20.22
Integral time reg.
humidifier 900s
--------------- P20.23
Derivative time reg.
humidifier 000s

Parameter for setting the Humidification integral time (PID)
Humidification regulation derivative time (PID)

20.22
20.23

--------------- P20.24
Cooling set point
lower limit:   24.0°C
--------------- P20.25
Cooling set point
upper limit: 32.0°C

Parameter for setting the Lower setpoint cooling limit and the Upper cooling setpoint limit

20.24
20.25

Содержание s-MEXT-G00 006

































































































































Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды

Mitsubishi Electric s-MEXT-G00 006, Техническое руководство

Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды