Mitsubishi Electric s-MEXT-G00 006 Скачать руководство пользователя страница 41

Страница: 41 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Mask of the terminal

Description

N. Par.

----------------P27.22
Minimum temp. for cool
compensation: 00.0 °C
----------------P27.23
Maximum temp. for cool
compensation: 10.0 °C

Parameters for setting

Offset start time (cooling)

Offset end time (cooling)

27.22

27.23

----------------P27.24
Maximum cool setpoint
compensation: 00.0 °C

Parameter for setting the maximum setpoint offset (cooling)

27.24

----------------P27.25
Minimum temp. for heat
compensation: 00.0 °C
----------------P27.26
Maximum temp. for heat
compensation: 10.0 °C

Parameters for setting

Offset start point (cooling)

Offset end point (Cooling)

27.25
27.26

----------------P27.27
Maximum heat setpoint
compensation: 00.0 °C

Parameter for setting the maximum setpoint offset (heating)

27.27

Regulations
2





Access mask to Regulations submenu 2. Press "Up" or "Down" to scroll the other masks and "Esc" to return to the
submenu.

Regulation 2 parameter
  NOT Available

It informs that no parameters are available in the menu for the unit.

User
Password:
0000

Access mask to “User” menu. Enter the “User” password for access.

Serial





Access mask to BMS management submenu. Press "Up" or "Down" to scroll the other masks and "Esc" to return
to the submenu.

--------------- P30.01
Enable supervision:
Y

Supervision presence configuration parameter

30.01

Содержание s-MEXT-G00 006

































































































































Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды

Mitsubishi Electric s-MEXT-G00 006, Техническое руководство

Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды