Mitsubishi Electric s-MEXT-G00 006 Скачать руководство пользователя страница 40

Страница: 40 / 128

TM_s-MEXT_ME28relC_00_12_19_EN

Technical manual

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Mask of the terminal

Description

N. Par.

--------------- P27.16
Enable Humidif.
Periodical Drain: N
--------------- P27.17
Time to wait for
Periodical Drain: 024h

Parameter for enabling the periodical drain function when the humidifier is in operation (N:disabled - Y:enabled)

Parameter for selecting the number of hours of continuous operation after which to perform the periodical drain

function

Visible only if the humidifier is internal.

27.16

27.17

--------------- P27.18
Enable Humidif.
Inactivity Drain: N
--------------- P27.19
Time to wait for
Inactivity Drain: 03d

Parameter for enabling the periodical drain function when the humidifier is inactive (N:disabled - Y:enabled)

Parameter for selecting the number of days of inactivity of the humidifier after which to perform draining

Visible only if the humidifier is internal.

27.18
27.19

--------------- P27.09
Dehumidification:
N

Dehumidifier configuration (N:disabled - Y:enabled)

27.09

--------------- P27.11
Damper config.:
N
--------------- P27.12
Damper opening time:
120sec

Parameters used to configure the air delivery damper (N:disabled - Y:enabled) and the

damper opening time

27.11

27.12

--------------- P27.13
Energy management:
N

Parameter to set the presence of the network transducer (N:absent - Y:present)

27.13

--------------- P27.14
System type:
3 -ph Aron
--------------- P27.15
Transformer ratio:
00020

Parameter for configuring the power supply system that can be 1-2-3 phases with balanced/unbalanced load, with

or without neutral (Default: system 3/4 unbalanced wires)

Parameter for configuring the input current transformer ratio (Default: 20)

27.14
27.15

Config CPT network: N
Serial baud CPT:4800
-3:INVALID DATA
-3:INVALID DATA
baud rate CPT OK

Chek Connections (Esc)

Mask for setting the correct transducer communication speed.

“Config CPT network” is used to set the correct speed in the transducer (from 9

600 to 19200). The transformer

ratio and the desired system type is sent to the transducer (P16.01 and P16.02).

The “NO ERROR” and “Transducer OK” messages indicate correct communication with the transducer for

changing speed.

“Ct ratio OK” and “System OK”

indicate the transformer ratio and the the system type indicated in parameters

P16.01 and P16.02 have been correctly sent to the transducer.

The various transducer configuration phases are indicated at the bottom of the mask. For further details see the
section relative to the network transducer.

--------------- P27.20
Enable setpoint
compensation: N
--------------- P27.21
Type of signal for
compensation: 0-1V

Parameters for setting

Setpoint offset function enable

Setpoint compensation signal type

27.20

27.21

Содержание s-MEXT-G00 006

































































































































Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды

Mitsubishi Electric s-MEXT-G00 006, Техническое руководство

Результаты поиска

Содержание s-MEXT-G00 006

Отзывы:

Похожие инструкции для s-MEXT-G00 006

Бренды по названию

Популярные бренды