Microscan EZ Match Скачать руководство пользователя страница 82

Страница: 82 / 431

4-14

EZ Match User’s Manual

Auxiliary Port Connections

Half Duplex Mode

Data Originating from the Auxiliary Port

• Auxiliary port data to the host is ignored if the

imager is in a polled mode.

• Auxiliary port data or read data is sent to the

host whenever it is received.

• Auxiliary port data is not echoed.

• Auxiliary port data to the host is always sent

without a preamble or postamble.

Data Originating from the Imager

• Data is transmitted to the auxiliary port at the

same time it is transmitted to the host.

• Data transmission conforms with all parameters

specified in the configuration menu (e.g. Preamble,
Postamble, End of Read Cycle).

Data Originating from the Host

• All host data is echoed to the auxiliary port in

unpolled mode.

Usage:

Useful when the user wants symbol data displayed on an auxiliary menu
close to the imager.

Definition:

Half Duplex Mode

all auxiliary port data and symbol data is sent directly

to the host. Symbol data is displayed on the auxiliary port menu at the
same time the data is sent to the host.

Serial Cmd.

<K101,aux port mode

,baud rate,parity,stop bits,data bits,daisy chain i.d.

status,daisy chain i.d.

Options:

2 = Half Duplex

Host

Aux.
Port

Imager

Host

Aux.
Port

Imager

Host

Aux.
Port

Imager

Содержание EZ Match
















































































































































































































































































































































































































































Результаты поиска

Содержание EZ Match

Отзывы:

Бренды по названию

Популярные бренды

Microscan EZ Match, Руководство пользователя

Результаты поиска

Содержание EZ Match

Отзывы:

Бренды по названию

Популярные бренды