Microscan EZ Match Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 431

Microscan EZ Match Скачать руководство пользователя страница 10

x

EZ Match User’s Manual

Statement of Agency Compliance

Statement of Agency Compliance

The EZ Match Imager has been tested for compliance with FCC (Federal Communications

Commission) regulations and has been found to conform to all applicable FCC Rules

and Regulations.

To comply with FCC RF exposure compliance requirements, this device must not be co-located

or operate in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

The EZ Match Imager has been tested for compliance with CE (Conformité Européenne)

standards and guidelines, and has been found to conform to applicable CE standards,

specifically the EMC requirements EN 55024, ESD EN 61000-4-2, Radiated RF Immunity

EN 61000-4-3, ENV 50204, EFT EN 61000-4-4, Conducted RF Immunity EN 61000-4-6,

EN 55022, Class B Radiated Emissions, and Class B Conducted Emissions.
The EZ Match Imager has been tested by an independent electromagnetic compatibility

laboratory in accordance with the applicable specifications and instructions.

«
...
8
9
10
11
12
...
»

Содержание EZ Match
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды