manualshive.com logo in svg

Microscan EZ Match, Руководство пользователя

Поделиться
Скачать
Microscan EZ Match Скачать руководство пользователя страница 191

EZ Match User’s Manual

8-7

I/O Parameters

When to Output Symbol Data

As Soon As Possible

End of Read Cycle

Assuming each operation was successful, the output would be as follows:

CP_,TP_,symbol data

Definition:

This command allows the user to choose when symbol data can be sent to 
the host.

Serial Cmd:

<

K705,

symbol data output status,

when to output

>

Default:

As Soon As Possible

Options:

0 = ASAP

1 = End of Read Cycle

Usage:

As Soon As Possible 

is useful in applications in which symbol data needs 

to be moved quickly to the host, typically when the host is making decisions 
based on symbol data.

Definition:

Enabling 

As Soon As Possible

 causes operation data to be sent to the 

host immediately after an index has qualified, or after an operation switch 
event has occurred.

Note:

 More than one decode might in fact be required to qualify as a Good 

Read, depending on how 

Decodes Before Output

 is set.

Note: 

When the read cycle is configured for output 

As Soon As Possible

, 

output filters are applied to each 

Multi-Operation

 index, but do not apply 

across Multi-Operation indexes. Output Filter # 1 will apply to the first output 
of each Multi-Operation index, and so on.

Usage:

End of Read Cycle

 is useful in timing-based systems in which the host is 

not ready to accept data at the time that it is decoded.

Definition:

Enabling 

End of Read Cycle

 means that operation data will not be sent to 

the host until the read cycle ends with a timeout or new trigger, or until all 
operations defined in 

Multi-Operation

 are completed.

Note:

 When the read cycle is configured for output at 

End of Read Cycle

, 

the output filters are applied to the final output of the read cycle. Therefore, 
all active filters are applied across all Multi-Operation indexes. 
For example, if 

3

 operations are enabled, one in each index, and if 

3

 filter 

positions are active, all 3 filters will be applied to each operation and the 
final output will be ordered according to the filters. See the table and resulting 
output shown below.

Index

Operation

Filter Position

Filter On

1

Bar Code Reader

1

Cap 

2

Tube Detection

2

Tube

3

Cap Detection

3

Nothing

Содержание EZ Match
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды