Microscan EZ Match Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 431

Microscan EZ Match Скачать руководство пользователя страница 79

EZ Match User’s Manual

4-11

Communications

Auxiliary Port Connections

The auxiliary port offers an alternative port that can be configured to communicate by
RS-232 in several modes, including daisy chain.
As with the host port parameters, the auxiliary port settings (baud rate, parity, stop bits,
and data bits) must be identical with those of the auxiliary device.

Auxiliary Port Mode

Baud Rate, Auxiliary Port

Usage:

An auxiliary port connects the imager to a remote display or to other readers
that can display or transfer data.

Definition:

These commands set the communication parameters with the auxiliary
port, which can be used to configure menus, send data to the host, display
data transmissions originating from the host, and relay data from other
imagers set in tandem (daisy chained).

Usage:

Can be used to transfer data faster or to match an auxiliary device.

Definition:

Determines the flow of data between the auxiliary port device(s), the
imager, and the host.

Serial Cmd:

<

K101,aux port mode

,baud rate,parity,stop bits,data bits,daisy chain i.d.

status, daisy chain i.d.

>

Default:

Disabled

Options:

0 = Disabled

1 = Transparent

2 = Half duplex

3 = Full duplex

4 = Daisy chain

5 = Command Processing

Usage:

Can be used to transfer data faster or to match an auxiliary device.

Definition:

The rate at which the imager and host transfer data back and forth.

Serial Cmd:

<

K101,

aux port mode,

baud rate

,parity,stop bits,data bits,daisy chain i.d.

status,daisy chain i.d.

>

Default:

115.2K

Options:

0 = 600

1 = 1200

2 = 2400

3 = 4800

4 = 9600

5 = 19.2K

6 = 38.4K

7 = 57.6K

8 = 115.2K

9 = 230K

«
...
77
78
79
80
81
...
»

Содержание EZ Match
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды