manualshive.com logo in svg

Microscan EZ Match, Руководство пользователя

Поделиться
Скачать
Microscan EZ Match Скачать руководство пользователя страница 269

EZ Match User’s Manual

10-11

Matchcode

New Master Pin

New Master Load Status

Definition:

If 

Matchcode

 and 

New Master Pin

 are enabled and the new master pin 

is momentarily connected to ground (must be held low for a minimum of 
10 ms) master symbol information will be loaded into the database based 
on the next read cycle that achieves a Good Read, starting with 

Index 1

. 

The 

Master Symbol Database

 will be loaded with all symbols decoded 

in the read cycle as long as it does not exceed the 

Number of Master 

Symbols

 parameter.

Serial Cmd:

<

K225,status

>

Default:

Disabled

Options:

0 = Disabled

1 = Enabled

Definition:

The new master status responds with the number of the next master 
position to be loaded, where 0 represents “idle” or “no master to be 
loaded.” 

Example:

 If the user has the 

Number of Master Symbols

 set to 

1

, and 

then either sends a 

<G>

 or toggles an active 

New Master Pin

, the state 

will be 

1

, and prior to reading and effectively loading position 

1

, the 

response to 

<NEWM>

 would be 

<NEWM/1>

. Once a symbol has been 

read and loaded, the status will be cleared: 

<NEWM/0>

.

Serial Cmd:

<

NEWM

>

Содержание EZ Match
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды