Microscan EZ Match Скачать руководство пользователя страница 77

Страница: 77 / 431

EZ Match User’s Manual

4-9

Communications

Polling Mode Options

RES-NAK Defaults

Note:

See

Polling Mode Data Flow Examples

in Appendix D for sample

Polling Mode

communication scenarios.

Note:

See

USB HID Interface

on page 4-24 for protocol information relating to USB.

Definition:

These parameters only take effect for

Polling Mode

<K140,5>

on the main

RS-232 or RS-422 ports (not on the Auxiliary Port), and are completely
independent of the

ACK/NAK Options

<K147>

The values of protocol characters can be changed, but the protocol events
cannot be disabled. The polling mode address is configured in the

<K140>

command (see

Poll Address

on page 4-7).

To enable true multidrop protocol, the RS422/485 port must be enabled,

<K102,1>

, in order to turn the transmitter on and off. If RS-232 is enabled

instead of RS422/485,

<K102,0>

, then

Polling Mode

will operate as a

Point-to-Point

polling protocol. This is because the RS-232 transmitter is

always left on when enabled.

Serial Cmd:

K148,

RES,REQ,STX,ETX,ACK,NAK

RES: (Reset)

REQ: (Request)

STX: (Start of Text)

ETX: (End of Text)

ACK: (Acknowledge)

NAK: (Negative Acknowledge)

Содержание EZ Match
















































































































































































































































































































































































































































Результаты поиска

Содержание EZ Match

Отзывы:

Бренды по названию

Популярные бренды

Microscan EZ Match, Руководство пользователя

Результаты поиска

Содержание EZ Match

Отзывы:

Бренды по названию

Популярные бренды