Microscan EZ Match Скачать руководство пользователя страница 176

Страница: 176 / 431

7-26

EZ Match User’s Manual

Pharmacode

Bar Width Status (Pharmacode)

Direction (Pharmacode)

Fixed Threshold Value (Pharmacode)

Definition:

If set to

Mixed

, the imager will autodiscriminate between narrow bars and

wide bars. If set to

All Narrow

, all bars will be considered as narrow bars. If

set to

All Wide

, all bars will be considered as wide bars. If set to

Fixed

Threshold

, it will use the fixed threshold value to determine whether the

bars are narrow or wide. The

Bar Width Status

setting will be ignored

when the imager is able to tell the difference between the narrow and the
wide bars.

Serial Cmd:

K477,

status,fixed symbol length status,fixed symbol length,minimum

number of bars,

bar width status

,direction,fixed threshold value

Default:

Mixed

Options:

0 = Mixed

1 = All Narrow
2 = All Wide
3 = Fixed Threshold

Definition:

Specifies the direction in which a symbol can be read.

Serial Cmd:

K477,

status,fixed symbol length status,fixed symbol length,minimum

number of bars,bar width status,

direction

,fixed threshold value

Default:

Forward

Options:

0 = Forward

1 = Reverse

Definition:

Used when

Bar Width Status

is set to

Fixed Threshold

. Defines the

minimum difference in pixels that will distinguish a narrow bar from a wide
bar.

Serial Cmd:

K477,

status,fixed symbol length status,fixed symbol length,minimum

number of bars,bar width status,direction,

fixed threshold value

Default:

Options:

1 to 65535

Содержание EZ Match
















































































































































































































































































































































































































































Результаты поиска

Содержание EZ Match

Отзывы:

Бренды по названию

Популярные бренды

Microscan EZ Match, Руководство пользователя

Результаты поиска

Содержание EZ Match

Отзывы:

Бренды по названию

Популярные бренды