Microscan EZ Match Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 431

Microscan EZ Match Скачать руководство пользователя страница 127

EZ Match User’s Manual

6-5

Read Cycle

Multisymbol

Number of Symbols

Usage:

Multisymbol is commonly used in shipping applications where a shipping
symbol contains individual symbols for part number, quantity, etc. This
feature allows on trigger to pick up all the symbols.

Definition:

Multisymbol

allows the user to define up to 100 symbols that can be read

in a single read cycle.

Conditions:

The following conditions apply:

• Each symbol must be different to be read, unless in

Rapid Capture

Mode

, configured for “triggered capture”.

• The maximum number of characters in a read cycle is 3,000 for all

symbols.

• All No Read messages are posted at the end of the data string, unless

output filtering is enabled.

• If more than one symbol is within the field of view at the same time,

symbol data may not be displayed in the order of appearance.

• If

Matchcode Type

is set to

Sequential

or if

Trigger

is set to

Continuous

Read 1 Output

, the imager will behave as if

Number of Symbols

were

set to

1

, regardless of the user-defined configuration.

Definition:

This parameter has no function when a

Multi-Operation

read cycle is

active. Each operation index (1 through 3) requires one qualified output for
each active operation.

Example:

If tube and cap detection are both enabled for operation index

1

,

the required number of symbols for that index would be

2

.

Important:

The same symbol, tube, or cap can be processed and qualified

by two different operations in the same read cycle.

Serial Cmd:

<

K222,number of symbols

, multisymbol separator

>

Default:

1

Options:

1 to 100

«
...
125
126
127
128
129
...
»

Содержание EZ Match
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды