manualshive.com logo in svg

Microscan EZ Match, Руководство пользователя

Поделиться
Скачать
Microscan EZ Match Скачать руководство пользователя страница 198

8-14

EZ Match User’s Manual

2D Symbology Qualification

Dimension Mode

Disabled

Decoded messages are output, but no attempt to qualify symbols or output 

Bad Symbol

 

or 

No Symbol

 messages is undertaken.

Bad/No Symbol Output

Checks first for decodes. If no symbol is decoded, checks for symbol dimension. If both 

Dimension 1

 and 

Dimension 2

 requirements are met, a 

Bad Symbol

 message is output. 

If neither are met, a 

No Symbol 

message is output.

Object Qualification

Checks first for matches to symbol dimension. If qualified, attempts to decode. If no 
decodes are found within the specified read cycle parameters, outputs a 

No Read

 message.

Enable Both

Same as 

Object Qualification

, except that if neither 

Dimension 1

 nor 

Dimension 2

 

qualifies, then a 

No Symbol 

message is output; if either 

Dimension 1

 or 

Dimension 2

 

qualifies, then a 

Bad Symbol

 message is output.

Definition:

Enables searches for symbol Dimension 1 and Dimension 2.

Serial Cmd:

<

K718,

finder pattern status,symbol size mode,symbol size 1,symbol size 

2,symbol size tolerance,

dimension mode

,dimension 1,dimension 

2,dimension tolerance,orientation mode,orientation value

>

Default:

Disabled

Options:

0 = Disabled

1 = Bad/No Symbol Output

2 = Object Qualification

3 = Enable Both

Содержание EZ Match
















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды