McHale F5400 Скачать руководство пользователя страница 90

Страница: 90 / 95

McHale

F5400

Baler

13.1.9 Net not cut correctly

13.1.10 Drop floor won’t move (up or down) - pick-up moves

Symptom

Reason

Solution

Net not cut correctly

Net tension is too loose as
it passes into netter

Adjust net tension system

Net not cut correctly

Not enough tension on the
net roll in the net box

Remove any crop build up
around the spring. Check
the tension springs. Adjust
or replace, if necessary.

Net not cut correctly

Blunt/rusty knife

Fit new knife

Net not cut correctly

Grease on knife (new
machine / machine after
winter storage)

Clean grease off knife
Use extreme caution and
protective clothing!

Net not cut correctly

Knife spring too slack

Adjust knife spring
pressure (located behind
the netter drive gears)

Symptom

Reason

Solution

Drop floor won’t move
(up/down)

Faulty hydraulic valve

Contact

McHale

dealer

Drop floor won’t move
(up/down)

Low power supply to the
control box

Check power source

Содержание F5400
































































































Результаты поиска

Содержание F5400

Отзывы:

McHale F5400, Инструкция оператора, Страница: 90 / 95

Результаты поиска

Содержание F5400

Отзывы: