McHale F5400 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 95

McHale F5400 Скачать руководство пользователя страница 62

McHale

F5400

Baler

62

In the case of wider swaths, i.e. >1.5 m; this size of windrow should be avoided, as in
this case a greater amount of material will continue to be fed to the outside of the baler.
As a result, a greater amount of material will be fed to the outer edges of the bale than
to the centre. This will result in concave-shaped bales.

Swath widths - correct & incorrect

9.3 Pick-up reel height adjustment

Before working in the field secure the pick-up guide wheels, in their operating position,
as shown. Use the appropriate hole in the adjusting bar so that the pick-up is balanced
and at the optimum working height with the pick-up tines being 2 cm above the ground.

Pick-up reel height adjustment

NOTE: Ensure the spool control lever is in the float position

When baling with this machine ensure that the control lever for the spool
operating the pick-up reel height adjustment is in the float position. If the
lever is not in the float position then the reel will be fixed in a set position
and will be unable to follow the ground contour.

NOTE: Wear and tear of pick-up tines

Working with the pick-up tines set too low will leave them susceptible to
breakage and rapid wear!

2 cm

«
...
60
61
62
63
64
...
»

Содержание F5400
































































































Отзывы:

Нет отзывов