manualshive.com logo in svg

McHale F5400, Инструкция оператора, Страница: 17 / 95

Поделиться
Скачать
McHale F5400 Скачать руководство пользователя страница 17

McHale

 

F5400

 Baler

17

It is the operator’s responsibility to ensure that there is no person in the 
‘Danger Zone’ while operating the machine, especially during start up.

Before repair or reassembly

Safe lifting gear of sufficient capacity must be used for machine assembly. 
All chains and slings used must be in good condition.

Before operation

The operator must ensure that the manufacturer’s instructions for attaching 
and detaching the machine are followed. This includes the drawbar 
attachment, the electric and hydraulic lines, in particular the lighting and brake 
system.

The operator must ensure that all covers are closed and all safety devices are 
in operating mode.

The operator must ensure that there is no person in the ‘Danger Zone’.

Always be familiar with the health and safety requirements that may be in 
force in the country of use.

During operation

While operating this machine on hilly or sloping ground the operator must take 
extra precautions, in particular the ‘Danger Zone’ is increased in such 
conditions as bales are more likely to roll away, causing a potential risk.

The operator must ensure that there is a minimum of 4 m clearance between 
the machine and any obstacle above, in particular electrical high voltage lines.

Particular care must be taken, if the machine is left idle for any extended 
period, to ensure that all sensors and safety features are working correctly.

Before travelling on public roads

The owner of this machine is obliged by law to ensure that every operator has 
a valid driving licence and is familiar with the road traffic regulations relating to 
the country of use.

Always ensure that the electronic control box and oil supply are switched off.

When parking, both wheels of this machine have to be blocked using the 
wheel chocks and hand brake (if fitted) should be applied according to the 
road traffic regulations, relating to the country of use.

WARNING: Do not carry people or animals on the machine

The operator must ensure that no persons or animals are carried on the 
machine at any time or are hidden under the machine (on the tractor 
persons are only allowed to sit on the relevant seats).

Содержание F5400
































































































Отзывы:

Нет отзывов