McHale F5400 Скачать руководство пользователя страница 88

Страница: 88 / 95

McHale

F5400

Baler

13.1.3 Chamber losing pressure

13.1.4 Issues with bale rotation/intake

13.1.5 Issue with bale quality/density

Symptom

Reason

Solution

Chamber losing pressure

Oil leak

Find leak and resolve

Chamber losing pressure

Relief valve loose /
restriction in relief

Contact

McHale

dealer

Symptom

Reason

Solution

Baler won’t take crop in
even though the bale
chamber is not full

Drop floor down - this can
cause problems with bale
rotation

Reset the floor to the
working position

Baler won’t take crop in
even though the bale
chamber is not full (straw)

The bale has stopped
rotating

Fit straw bar (Available
from

McHale

dealer)

Symptom

Reason

Solution

Issues with bale quality/
density

When closing the door the
spool is moving into the
float position, as a result
the chamber is not being
pressurised

Attach the door functions
to the tractor spool without
a float position

Issues with bale quality/
density

Density set too low for the
crop conditions

Increase the density

Issues with bale quality/
density

Crop build up at the
chamber door lower
closing point

Clean away loose crop
Use extreme caution!

Issues with bale quality/
density

Ground speed too high

Reducing ground speed
will allow the machine to
pack the bale better

Machine making bales
with soft edges/corners

The centre of the bale is
being overfilled

(See ‘Swath preparation’)

Содержание F5400
































































































Результаты поиска

Содержание F5400

Отзывы:

McHale F5400, Инструкция оператора, Страница: 88 / 95

Результаты поиска

Содержание F5400

Отзывы: