McHale F5400 Скачать руководство пользователя страница 12

Страница: 12 / 95

McHale

F5400

Baler

2.4 General dimensions & specifications

* Check with national road traffic regulations in the individual country!

2.5 Tractor attachment

(*) May not be available in all countries, check with your

McHale

dealer for availability

in your country.

Units are given in both metric and UK imperial values, with the latter shown in brackets.

Transport length

4.53 m (178”)

Transport width

2.55 m (100”)

Transport height

2.70 m (106”)

Transport weight

3,620 kg (7,981 lbs)

Tyre dimensions

13.5/75-430.9

Tyre pressure

2.07 bar (30 psi)

Tyre dimensions (pick-up reel)

170/60-8

Tyre pressure (pick-up reel)

2.07 bar (30 psi)

Maximum road speed

40 km/h (25 mph)

Brake system (optional)

Hydraulic brakes
Air brakes *

Drawbar

Low drawbar
High drawbar *

PTO speed

540 rpm

Lighting

12 V / 7-pin socket

Electrics

12 V, 20 A euro socket

Hydraulic systems

Open-centre

Minimum pressure

165 bar (2,393 psi)

Minimum flow rate

30 l/min (6.6 gal/min)

Содержание F5400
































































































Результаты поиска

Содержание F5400

Отзывы:

McHale F5400, Инструкция оператора, Страница: 12 / 95

Результаты поиска

Содержание F5400

Отзывы: