McHale F5400 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 95

McHale F5400 Скачать руководство пользователя страница 46

McHale

F5400

Baler

46

Type A

- The following applies to the swing down fixed length stand (low hitch):



Transport working position: While using the machine, ensure that the drawbar
stand (1) is raised fully with stand pin (3) in the alternate hole position.



Storage position: Ensure that the stand pin (3) is properly placed in the lower
slot to prevent the stand from collapse.



Swing down the PTO shaft stand (2) in an upright position in order to support
the PTO shaft (4).

Type B

- The following applies to swing down screw stand (low hitch):



Similar to type A, except stand pin (3) is in the upper slot, in the transport
(working) position. It should be wound up and retracted fully, as shown, before
removing the handle. The main difference being, that the drawbar height is
now fully adjustable.

.

Type A - swing down fixed length stand (low hitch)

Transport (working) position

Storage position

PTO shaft stand (type A & B)

Transport (working) position

Storage position

1

Type B - swing down screw stand (low hitch)

Transport (working) position

Storage position

1

3

1

3

2

4

3

1

2

3

1

3

1

«
...
44
45
46
47
48
...
»

Содержание F5400
































































































Отзывы:

Нет отзывов