McHale F5400 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 95

McHale F5400 Скачать руководство пользователя страница 15

McHale

F5400

Baler

15

As with all machinery, learn all operations and use controls by reading this manual
thoroughly. Do not attempt to let anyone operate this machine without being fully
instructed.

3.3 Store all items carefully

Store all attachments in a secure and safe manner so as to prevent
items from falling. Keep storage areas clear of bystanders and
children.

3.4 Protective clothing

Always wear clothing and safety equipment that is fit for the job at
hand, never wear loose clothing. In the event of loud noises, wear
suitable protective hearing devices. Use of mobile phones or radio/
music headphones are not recommended while operating
machinery as these impair the operator’s attention.

3.5 In case of emergencies

In the event of any accident, emergency equipment should be kept
close at hand. A first aid kit and fire extinguisher along with
emergency phone numbers should always be available to machine
operators.

3.6 Stay clear of rotating elements

Serious injury or death can result from entanglement of clothing or body parts with PTO
shafts, drivelines and other rotating and moving components.

Keep all guards in place at all times, only wear close fitting clothing and ensure that the
tractor engine has stopped, the key has been removed and that the PTO has stopped
turning before carrying out any adjustments, connections or cleaning of PTO driven
equipment.

3.7 Operating the machine

In order to avoid serious injury or even death by being pulled into the machine:



Never attempt to feed net or crop into the baling chamber or attempt to unplug
pick-up area while the baler is running.



Disengage the PTO, apply handbrake, shut the tractor engine off and remove
the key from the ignition.



Stand well clear of the machine and tractor when the machine is operating.

«
...
13
14
15
16
17
...
»

Содержание F5400
































































































Отзывы:

Нет отзывов