McHale F5400 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 95

McHale F5400 Скачать руководство пользователя страница 14

McHale

F5400

Baler

14

3

General safety

3.1 Be aware of all safety information

Follow all safety precautions and practice safe operation of machinery, at all times.

Warning, caution, note & environment messages:

When reading this manual, pay particular attention when you see the symbols below
i.e. warning, caution, note and environment. They will be used at various points in this
manual and may also appear on safety decals on the machine. The purpose of these
messages is to ensure that the most important information stands out from the rest of
the text.

WARNING

: This symbol indicates a potentially hazardous situation,

that if not avoided could result in machinery damage, personal injury
or even death

.

CAUTION

: This symbol indicates a potentially hazardous situation,

that if not avoided could result in machinery damage or personal
injury

.

NOTE

: This symbol is used to identify special instructions or

procedures which, if not followed strictly, could result in machinery
damage.

ENVIRONMENT

: This symbol reminds you to respect the

environment in relation to the correct disposal of waste material.

3.2 Follow all safety instructions

Using this manual, read all safety instructions and messages, and
be aware of the meanings of all safety decals

(See ‘Safety warnings

& instructions explained’)

. If safety decals are damaged or missing

due to wear and tear or component replacement, ensure that they
are replaced. Refer to the spare parts book provided to see the
spare part codes for the relevant decals, which are available from
your

McHale

dealer.

«
...
12
13
14
15
16
...
»

Содержание F5400
































































































Отзывы:

Нет отзывов