McHale F5400 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 95

McHale F5400 Скачать руководство пользователя страница 21

McHale

F5400

Baler

21

4.3 Noise level



The European Regulation 86/188/EEC directs employers and employees to
control the noise level at work. The noise level at field work may differ
according to the tractor, ground, crops and other environmental conditions.



In normal conditions, whilst driving the machine, the noise level to the driver’s
ear does not exceed 70 dB (A) with the rear screen of the tractor cabin open.
The common noise level of the machine and the tractor is primarily influenced
by the tractor noise (radio is an additional noise source). It is recommended to
operate this machine with closed cabin windows.

4.4 Fire precautions



Be aware that crops are easily inflammable.



Do not smoke or make use of any open fire next to the machine.



A functioning fire extinguisher should always be available on the tractor.



The machine is to be kept clear of oil, grease, crops, string, plastic or any
other flammable material at all times.



Do not continue to work with overheated parts, cables or pipes, unless you
have identified and eliminated the reason for overheating.

4.5 Special safety devices/instructions



According to European safety regulation, the covers of this machine are
designed to be opened only by the aid of a special tool and to be closed
without a tool. To unlock the covers, the locks should be turned slightly anti-
clockwise with a 13 mm spanner or flat blade screwdriver. To lock the covers
push the cover towards the chassis until the fasteners lock into place. It is
forbidden to operate the machine without the covers or with them open. The
owner of the machine is obliged, by law, to ensure that all covers are installed
on the machine and are in good functioning condition.



When maintenance or repair work has to be carried out at the open bale
chamber, the chamber door lever valve must be in the locked position. Before
the chamber door can be closed it has to be unlocked again.

(See ‘Chamber

door lock’)



Caution should always be taken when feeding in the net roll or making any
adjustments to the netter configuration as the netter knife is extremely sharp!

«
...
19
20
21
22
23
...
»

Содержание F5400
































































































Отзывы:

Нет отзывов