manualshive.com logo in svg

McHale F5400, Инструкция оператора, Страница: 20 / 95

Поделиться
Скачать
McHale F5400 Скачать руководство пользователя страница 20

McHale

 

F5400

 

Baler

20

4

Specific safety warnings

4.1  Electronic safety warnings

This machine is equipped with electronic parts and components which 
comply to the EMC directive 2004/108/CE but still may be influenced by 
electromagnetic transmissions of other apparatus, such as welding machines, 
etc.

Check electric cables regularly for signs of breakage or wear. If in doubt 
always replace.

Do not modify any safety circuits (faulty safety circuits will cause risks).

4.2  Hydraulic safety warnings

The maximum pressure in the hydraulic system of this machine should not 
exceed 210 bar.

Always ensure the system is not under pressure before working on the 
machine. Oil under pressure can penetrate the skin and cause injury. Beware 
of pipes under accumulator pressure, depressurise lines by unthreading 
connections extremely slowly.

Hydraulically actuated devices must be blocked mechanically against 
movement, before working on the machine.

If any hoses are removed or replaced ensure they are marked and re-installed 
to the correct position during re-assembly.

Check hoses regularly for signs of leakage or wear. If in doubt always replace. 
The recommended maximum working time of hoses should not exceed 
5 years. Only use exact specification 

McHale

 genuine replacement parts.

Do not work on hydraulic systems unless you are qualified to do so. This work 
should only be carried out by qualified persons or your 

McHale

 dealer.

Содержание F5400
































































































Отзывы:

Нет отзывов