McHale F5400 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 95

McHale F5400 Скачать руководство пользователя страница 45

McHale

F5400

Baler

45

6.9 Wheel chocks

Wheel chocks are provided to secure the machine wheels anytime the machine is to
be detached from the tractor, or if the machine is to be stored or parked up. They are
located on both the left and right of the back panels, on the rear of the machine.

Wheel chocks

6.10 Drawbar & PTO shaft stand usage

There are three types of drawbar stands available on the machine, depending on the
country of use, one will come as standard:

1.

A swing down fixed length stand (low hitch) -

Type A

2.

A swing down screw stand (low hitch) -

Type B

3.

A fixed screw down stand (high hitch) -

Type C

The drawbar stands are to be used every time the machine is disconnected from the
tractor. The PTO shaft stand must also be used to support the PTO shaft.

Tyre type

Pressure

13.5/75-430.9

2.07 bar (30 psi)

460/65-20 (optional)

1.38 bar (20 psi)

500/50-17 (optional)

1.38 bar (20 psi)

500/50-22.5 (optional)

1.38 bar (20 psi)

520/55R22.5 (optional)

1.38 bar (20 psi)

170/60-8 (pick-up tyre)

2.07 bar (30 psi)

CAUTION: All stands must be rested on a solid footing

All stands must be rested on a solid footing, on level ground and also
supplied wheel chocks must be used.

«
...
43
44
45
46
47
...
»

Содержание F5400
































































































Отзывы:

Нет отзывов