McHale F5400 Скачать руководство пользователя страница 87

Страница: 87 / 95

McHale

F5400

Baler

Troubleshooting

13.1 Troubleshooting overview

This section has been compiled by

McHale

service personnel in conjunction with

McHale

importers and dealers.

It outlines some common problems which can occur and acts as a quick reference
section or check list to resolve the problem. It is important to note that it outlines the
common problems and to this effect it is not exhaustive.

Should you experience additional problems which you need help with; please do not
hesitate to contact your

McHale

dealer.

13.1.1 Pick-up slip clutch going off easily

13.1.2 PTO slip clutch going off easily

Symptom

Reason

Solution

Pick-up slip clutch going
off easily or machine
breaking tines

Pick-up set too close to
the ground

Adjust the pick-up to a
higher position. Tines
should not be getting
caught in the ground.

Pick-up slip clutch going
off easily

Pick-up chains loose

Tighten the pick-up chains

(See ‘Chain adjustments’)

Symptom

Reason

Solution

PTO slip clutch going off
easily

Rotor chain loose

Tighten the rotor chain
and check, as specified

PTO slip clutch going off
easily

Poor swath preparation

Prepare the swath in line
with the recommendations
in the machine setup

(See ‘Swath preparation’)

PTO slip clutch going off
easily

Chamber pressure /
ground speed too high

Reduce

Содержание F5400
































































































Результаты поиска

Содержание F5400

Отзывы:

McHale F5400, Инструкция оператора, Страница: 87 / 95

Результаты поиска

Содержание F5400

Отзывы: