manualshive.com logo in svg

Matrix SIMADO GFXD1111S, Системное руководство

Поделиться
Скачать
Matrix SIMADO GFXD1111S Скачать руководство пользователя страница 21

Matrix SIMADO GFXD1111S V3 System Manual

15

Switching ON SIMADO GFXD1111S

After connecting the system as shown above, switch ON the power supply.

At Power ON (During Reset Sequence):

•

LED labeled as 'PWR' will glow green continuously.

•

LED labeled as 'FXO', 'FXS' and 'RDY' will blink (RED) four times (500ms On, 500ms Off) and then turns 
Off. 

•

LED labeled as 'NW' starts blinking (RED) after few seconds of Power On. It indicates the network 
availability.

•

When SIM Card is detected, LED labeled as 'RDY' will start blinking (RED) slowly (1 sec On- 1 sec Off) till 
successful network registration. After that, it will glow RED continuously. Network registration takes 
approximately 90 seconds. 

•

LED labeled as 'RDY' will blink (RED) fast (100 msec On- 100 msec Off) if SIM Card is absent or 
deactivated or SIM PIN is faulty or SIM PUK is required. 

During Normal Functioning:

Following table shows various LED indications during the normal functioning of the system:

LED

Activity

Indication

PWR

ON

Indicates that GFXD1111S is power On.

OFF

Indicates that GFXD1111S is power Off.

Blinking

NA

RDY

ON

SIM Card is present and active.

OFF

GFXD1111S powered On but SIM Card is not detected.

Blinking (100 msec 
On-100 msec Off)

SIM card is absent or de-activated or SIM PIN is faulty or SIM PUK is 
required.

Blinking (1 sec On-1 
sec Off)

SIM Card detected but is not registered with the network.

Blinking (2000 msec 
On- 2000 msec Off)

a

a. Applicable only when Call Minutes feature is enabled for Mobile Port. (Refer 

“Call Minutes”

 for more details)

Indicates that either:

1.

20 minutes or less than 20 minutes of free Call Minutes are left.
Or

2.

The free Call Minutes allocated to the Mobile Port are utilized.

FXS

ON

Indicates that FXS Port is OFF-Hook.

OFF

Indicates that FXS Port is ON-Hook.

Blinking

Indicates that FXS Port is ringing.

FXO

ON

Indicates that FXO Port is OFF-Hook.

OFF

Indicates that FXO Port is ON-Hook.

Blinking

Indicates that FXO Port is ringing.

NW 
(controlled 
by Module)

ON

NA

OFF

SIM module is OFF.

Blinking

Slow

SIM module is ON and is registered with the network i.e. network is available.

Fast

SIM module is ON but is not registered with the network i.e. network not 
available.

Содержание SIMADO GFXD1111S



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды