manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 5

 

 

 

 

QUI-1122 

Page 5 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

1.4

 

Important safety warnings 

There are several important safety notices to keep in mind when installing and using this instrument. 

1.4.1

 

Labels/symbols 

Throughout this manual symbols will appear where carrying out an operation may involve hazards. 
Symbols and warnings also appear on the instrument, and these should be adhered to at all times. 
Markes International can accept no liability for failure to do so.  

 

BURN HAZARD

 

A hot surface may result in a burn injury. 

 

INSTRUMENT/PART DAMAGE 

Damage to the instrument or module may occur. This damage may not be covered under 
the standard warranties. 

 

LIFTING HAZARD 

Injury may occur if proper lifting procedures are not followed. 

 

WARNING

 

General warning symbol to alert the user that personal injury or instrument damage may 
occur if the instrument is improperly used or if instructions are not followed correctly. 

 

DISPOSAL

 

This label indicates the instrument must not be disposed in regular waste but in 
accordance with the WEEE scheme. 

 

1.4.2

 

Mains voltages 

 

 

 

 

Ensure at all times that the plug (electrical isolator) can be easily and quickly 
accessed during equipment use. 

 

The instrument must be suitably earthed via the power cord. 

NOTE

:  Voltages within the instrument will be a maximum of 24 V. Although there is 

decreased risk of serious injury, these internal voltages should still be treated 
as dangerous. Contact with any live parts may cause personal injury and/or 
instrument damage. 

 

 

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды