manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 24

 

 

 

 

QUI-1122 

Page 24 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

3.6

 

Sample line connection 

Sample lines are connected to the 
1/8” fittings on the front of the Air 
Server-xr (8 channel model shown 
opposite). 

The lengths of 1/8” PTFE tubing 
included in the Air Server-xr shipping 
kit can be used for sample connection 
(cut to required lengths). 

 

NOTE

: The Air Server-xr accessory is 

only rated to 50 psig. Standards or 
samples at pressures higher than this 
must be regulated to lower pressures 
using appropriate pneumatic controls 
before they are connected to an inlet 
on the Air Server-xr. 

 

 

3.7

 

Configuring the dryer (optional) 

The Markes International dryer incorporates a semi-permeable membrane which selectively eliminates 
water and polar organic compounds from a gas or air stream. The selectivity of the dryer is, sometimes, an 
advantage, for example when monitoring multiple trace level hydrocarbons in real-time in ambient air 
using GC and FID.  

The nafion dryer assembly is shown 
opposite. 

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды