manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 18

 

 

 

 

QUI-1122 

Page 18 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

Remove the back cover by sliding it backwards. 

 

 

Place the 1/16 x 0.4 mm (U-FV001 (pk 10)) ferrule 
onto the union then thread the 1/16-inch stainless 
steel Swagelok type nut (SERZ-0157) on loosely 

 

Pull ~ 20 cm of fused silica from the PTFE line 
casing. Cut off the first few mm of fused silica 
using an approved capillary cutting tool.  

Make a mark 20 mm from the end of the fused 
silica using typing white-out fluid or an alternative 
marker.  

Gently feed the fused silica through the 1/16” nut 
and ferrule until the mark is reached.  

Tighten the nut to trap the fused silica and then 
tighten a further 1/2 turn using one of the 8 mm 
wrenches (spanners) provided in the shipping kit.  

 

 

Do not over tighten or the ferrule will 
become distorted. 

20 mm 

insertion 

depth 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды