manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 35

 

 

 

 

QUI-1122 

Page 35 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

6.

 

Configuration of UNITY–Air Server-xr Electronic Gas Control – instrument specific 
guides  

6.1

 

UNITY–Air Server-xr Electronic Gas Control with the Agilent 6890GC 

NOTE:

   To complete this installation the following 6890 parts are recommended.  They can be ordered 
directly from Agilent. 

 

Part no. 

Description 

Quantity 

G2131-80500 

Replacement 2 port EPC block  

1 

1390-1022 

Screw 

1 

 

However, if these parts are not available at installation both the carrier gas and septum purge lines 
running between the EPC module and the Split/Splitless injector must be cut and extended using 1/8” 
unions and green PEEK tubing in order to facilitate connection to UNITY–Air Server-xr. 

NOTE:

   When installing onto an existing 6890GC the firmware on the GC must be A.03.08 or later (for A-

series) or N.04.09 (for N-series).  To check the firmware version, use the keyboard on the GC, 
press > Options > Diagnostics > Instrument Status and then scroll down to ‘Version’ where you will 
see the version of the firmware running on the instrument. 

6.1.1

 

Procedure 

 

Remove the top rear cover on the GC to provide access to the EPC module that is going to be used to 
regulate the carrier gas supply to UNITY–Air Server-xr. 

 

 

 

Removing the rear panel to access EPC modules 

 

Remove the 3 port EPC block assembly from the split/splitless EPC module.  

 

Fit the replacement EPC block assembly, and route the 1/16” tubing through the rear panel of the GC 
and towards the UNITY–Air Server-xr. 

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды