manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 31

 

 

 

 

QUI-1122 

Page 31 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

After making any necessary changes in the Configuration or Gas & flows Tab click ‘OK’ and when 
prompted by the following message choose ‘Apply changes’ to close the software. On reopening the 
software will be correctly configured.    

 

4.2.2

 

Detecting the UNITY–Air Server-xr 

Ensure that the all gas supplies to the system - especially the dry air or nitrogen purge gas used for UNITY-
xr valve actuation and purging the cold trap box - are on. 

Having checked the above, switch UNITY–Air Server-xr on using the switch located on the back panel of 
UNITY-xr. 

If communications between the PC and UNITY–Air Server-xr are established successfully the instrument 
status will change to Idle. If for some reason, communication is not established the instrument status will 
remain as Offline.  

 

 

 

 

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды