manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 4

 

 

 

 

QUI-1122 

Page 4 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

1.

 

Preface 

This manual provides detailed instructions for the use of the UNITY–Air Server-xr. It details the 
software/hardware interface and procedure for the installation of this instrument. 

1.1

 

Notices 

No part of this manual may be reproduced in any form or by any means (including electronic storage and 
retrieval or translation into a foreign language) without prior agreement and written consent from Markes 
International. 

Please note that the material contained in this document is subject to being changed, without notice, in 
future editions. Markes International shall not be liable for errors or for incidental or consequential 
damages in connection with the supply, use or performance of this document or of any information 
contained herein, unless a separate agreement between Markes International and the user should take 
precedence. 

1.2

 

Warranty 

UNITY–Air Server-xr is designed for laboratory use only. It is not intended for use in domestic 
establishments or establishments directly connected to a low-voltage power supply network that supplies 
buildings used for domestic purposes. Where equipment is used in a field placement environment, care 
must be taken to ensure that the instrument is not exposed to detrimental conditions,

 i.e.

 rain, wind, or 

sun. Exposure may diminish the performance, cause damage to the instrument and/or cause the 
equipment to become unsafe to the user. 

If the equipment is not used in a way specified by Markes International, the safety protection provided by 
the equipment may be reduced. Furthermore, system failures arising from such use may not be covered in 
standard warranty and/or service contract agreements. 

1.3

 

Regulatory compliance 

 
The instrument is designed and manufactured under a quality system registered to ISO 9001. 
 
The instrument complies with the essential requirements of the following applicable European Directives, 
and carries the CE mark accordingly: 

o

 

Low voltage Directive 2014/35/EU 

o

 

EMC Directive 2014/30/EU 

 

The instrument conforms to the following product safety standards: 

o

 

IEC 61010-1/EN 61010-1 

o

 

Canada: CSA C22.2 No.61010-1 

o

 

USA: ANSI/UL 61010-1. 

 

The instrument conforms to the following regulation on electromagnetic compatibility (EMC): 

o

 

 IEC 61326-1/EN 61326-1.

 

 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды