manualshive.com logo in svg

Markes International UNITY-Air Server-xr, Руководство по установке

Поделиться
Скачать
Markes International UNITY-Air Server-xr Скачать руководство пользователя страница 10

 

 

 

 

QUI-1122 

Page 10 

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

2.4.3

 

 Pressure controlled carrier gas supply 

Helium is invariably used as the carrier gas for capillary chromatography and nitrogen for packed column 
or sensor work. 5.0 grade (i.e. 99.999%) or higher purity helium / nitrogen gas is recommended in either 
case.   

UNITY–Air Server-xr requires a regulated supply of carrier gas at a pressure to suit the analytical column / 
system selected.  The UNITY–Air Server-xr gas flow path has minimum (<2 psi) impact on total system 
impedance.  Suitable pneumatic control for the carrier gas may already be available on your GC.  The 
performance of most common capillary columns is optimised at between 1 and 2 ml/min typically 
requiring between 10 and 30 psi head pressure.   

Previously approved and correctly rated external gas regulator should be used with this unit. Maximum 
inlet pressure must not exceed 60 psi. 

The pressure in the laboratory carrier gas line should be at least 10 psi higher than that supplied to 
UNITY–Air Server-xr.  

2.4.4

 

Filters  

Deoxo and organic filters should be included in the carrier gas line just upstream of connection to the 
UNITY–Air Server-xr - GC analytical system (see Accessories for Thermal Desorption catalogue). 
 

Содержание UNITY-Air Server-xr
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды